XC8 Archives - electroSome

Digital Alarm Clock using PIC Microcontroller and DS3234 RTC

Here is a digital alarm clock made using PIC 18F4520 Microcontroller and DS3234 RTC (Real Time Clock). This project is for educational purposes or can be used as a reference for integrating DS3234 RTC. DS3234 is a very accurate RTC IC with integrated on chip temperature compensated crystal oscillator. It can be integrated with a microcontroller using SPI bus. This project is developed using MPLAB XC8 compiler. Components Required PIC 18F4520 MicrocontrollerDS3234 RTC20MHz Crystal 4x3 Keypad16x2 LCD10KΩ preset5V buzzerLEDBC547 TransistorCapacitor...

April 11, 2020By Ligo GeorgeEmbedded, PIC Microcontroller, ProjectsDS3234, Embedded, Microcontroller, MPLAB, MPLAB XC8, PIC, PIC Microcontroller, Proteus, RTC, SPI, XC814 CommentsRead more...

SPI Communication with PIC Microcontroller – MPLAB XC8

SPI (Serial Peripheral Interface) is a full duplex synchronous serial communication interface used for short distance communications. It is usually used for communication between different modules in a same device or PCB. SPI devices communicates each other using a master slave architecture with a single master. SPI Communication SPI is called as a 4-wire bus as it requires four wires for its communication as shown above. In the case of single slave communications we need only 3 wires, as slave select (SS) is...

May 1, 2017By Ligo GeorgeMPLAB XC8, PIC Microcontroller, Tutorials16F877A, MPLAB, PIC, SPI, XC82 CommentsRead more...

I²C Communication with PIC Microcontroller – MPLAB XC8

I2C or IIC or I2C stands for Inter-Integrated Circuit. It is a very popular multi-master, multi-slave serial communication interface developed by Philips. I2C uses two bidirectional open drain data lines, Serial Data (SDA) and Serial Clock (SCL) with pull up resistors as shown below. Unlike UART, you can connect and communicate to multiple devices using the same I2C bus. I2C Communication I2C is a master slave protocol. It means that devices connected to I2C bus will be either master or slave. The master is the...

April 11, 2016By Ligo GeorgeMPLAB XC8, PIC Microcontroller, Tutorials16F877A, I²C, MPLAB, MPLAB IDE, MPLAB X IDE, PIC, XC869 CommentsRead more...

Using ADC of PIC Microcontroller – MPLAB XC8

In this tutorial we will learn, how to use the ADC module of a PIC Microcontroller using MPLAB XC8 compiler. For demonstration we will use the commonly available PIC 16F877A microcontroller. Every physical quantity found in nature like temperature, humidity, pressure, force is analog. We need to convert these analog quantities to digital to process it using a digital computer or a microcontroller. This is done by using Analog to Digital Converters. An Analog to Digital Converter or ADC is a device...

November 12, 2015By Ligo GeorgeMPLAB XC8, PIC Microcontroller, Tutorials16F877A, Microcontroller, MPLAB, MPLAB XC8, PIC, Proteus, Tutorials, XC828 CommentsRead more...

Generating PWM with PIC Microcontroller – MPLAB XC8

Pulse Width Modulation (PWM) is the one of the simple and most commonly used technique to produce analog voltages from digital signals. It has a wide variety of applications such as Digital to Analog Converter (DAC), DC Motor Speed Control, Sine Wave Inverters, Brightness control etc. PWM signals are ON - OFF signals (HIGH or LOW) (hence the name Pulse) whose HIGH or ON duration is changed (hence Width Modulation) in accordance with our requirements. The fraction of time period for...

May 21, 2015By Ligo GeorgeMPLAB XC8, PIC Microcontroller, Tutorials16F877A, CCP, Microcontroller, MPLAB, MPLAB IDE, MPLAB XC8, PIC, PWM, XC832 CommentsRead more...

Using UART of PIC Microcontroller – MPLAB XC8

UART stands for Universal Asynchronous Receiver / Transmitter. It is a very popular serial communication interface which provides Full Duplex communication between two devices. UART uses two data lines for sending (TX) and receiving (RX) data. Ground/Reference of both devices should be made common. As the name indicates it is an asynchronous communication interface, which means that it doesn't need to send CLOCK along with data as in synchronous communications. UART is the communication interface used by our old computer's...

October 3, 2014By Ligo GeorgeMPLAB XC8, PIC Microcontroller, TutorialsEmbedded, Microcontroller, MPLAB, MPLAB XC8, PIC, Proteus, Tutorials, XC854 CommentsRead more...

Interfacing LCD with PIC Microcontroller – MPLAB XC8

In this tutorial we will see How to Interface a 16x2 character LCD module with PIC 16F877A Microcontroller using MPLAB X IDE and MPLAB XC8 C Compiler. 16x2 Character LCD is a very basic and low cost LCD module which is commonly used in electronic products and projects. 16x2 means it contains 2 rows that can display 16 characters. Its other variants such as 16x1 and 16x4 are also available in the market. In these displays, each character is displayed...

August 18, 2014By Ligo GeorgeMPLAB XC8, PIC Microcontroller, TutorialsEmbedded, Microcontroller, MPLAB, MPLAB X IDE, MPLAB XC8, PIC, Proteus, Tutorials, XC8136 CommentsRead more...

Interfacing HC-SR04 Ultrasonic Sensor with PIC Microcontroller

HC-SR04 Ultrasonic Distance Sensor is a popular and low cost solution for non-contact distance measurement function. It is able to measure distances from 2cm to 400cm with an accuracy of about 3mm. This module includes ultrasonic transmitter, ultrasonic receiver and its control circuit. HC-SR04 module has 4 pins : VCC - 5V, +ive of the power supply TRIG - Trigger Pin ECHO - Echo Pin GND - -ive of the power supply TRIG and ECHO pins can be used to interface this module with a microcontroller...

August 12, 2014By Ligo GeorgeEmbedded, MikroC, MPLAB XC8, PIC Microcontroller, PIC Microcontroller, ProjectsHC-SR04, Microcontroller, MikroC, MikroC Pro, MPLAB, MPLAB XC8, PIC, Tutorials, Ultrasonic, XC8226 CommentsRead more...

Tag - XC8