Tag - MikroC

Ultrasonic Distance Sensor

Interfacing Ultrasonic Distance Sensor : ASCII Output with PIC Microcontroller

In some of our projects, we may want to measure the distance of an object from a point. Ultrasonic Distance Sensors are the best sensor which provides stable, accurate, precise, non-contact distance measurements from 2cm to 4m. Ultrasonic Sensors can be used to measure distance between moving or stationary objects. Being very accurate and stable, these devices find large number of applications in robotics fields. For example it can be used as an excellent replacement for IR sensors in  a Micromouse. In...

March 7, 2013By Embedded, MikroC, PIC Microcontroller, PIC Microcontroller, Projects, Tutorials, , , , 92 CommentsRead more...
relay

Interfacing Relay with PIC Microcontroller

A relay is an electromagnetic switch which is used to switch High Voltage/Current using Low power circuits. Relay isolates low power circuits from high power circuits. It is activated by energizing a coil wounded on a soft iron core. For detailed working of relay please visit this page. A relay should not be directly connected to a microcontroller, it needs a driving circuit. A relay should not be connected directly to a microcontroller due to following reasons.. A microcontroller is not able...

March 2, 2013By MikroC, PIC Microcontroller, Tutorials, , , , 42 CommentsRead more...
dc motor

DC Motor Speed Control using PWM with PIC Microcontroller

I already posted about Interfacing DC Motor with PIC Microcontroller. In our robotics applications we may have to control the speed of the DC Motor. In this tutorial we will see how to control the speed of a DC Motor using Pulse Width Modulation (PWM). By using PWM we can easily control the average power delivered to a load and by thus we can easily control the speed of the DC Motor. You may think that a variable resistor in series...

January 26, 2013By MikroC, PIC Microcontroller, Tutorials, , , 143 CommentsRead more...
PIC16F877A

Generating PWM with PIC Microcontroller using CCP Module

PWM is a technique used to generate analog output signal using digital signals. It is commonly used to control average power delivered to a load, motor speed control, generating analog voltage levels and for generating analog waveforms. CCP Modules are available with a number of PIC Microcontrollers. CCP stands for Capture/Compare/PWM. Using PWM module is far more easier and cost effective than using extra chips for PWM generation.  MikroC Pro for PIC Microcontroller provide built-in library for PWM which makes our...

January 19, 2013By MikroC, PIC Microcontroller, Tutorials, , , , 114 CommentsRead more...

Expanding IO Ports of PIC Microcontroller using MCP23S17

Usually a microcontroller comes with a limited number of IO ports called General Purpose Input Output (GPIO) ports. But some applications require more IO ports than that available on a microcontroller. In these cases we can use IO Port Expanders to increase the IO capability of a microcontroller. MCP23017 and MCP23S17 are two such 16 bit IO expander with Serial Interface  manufactured by Microchip. MCP23017 uses high speed I2C interface while MCP23S17 used high speed SPI interface. MCP23S17 In this tutorial we...

January 13, 2013By MikroC, PIC Microcontroller, Tutorials, , , 4 CommentsRead more...
PIC16F877A

PIC to PIC Communication using UART

Introduction PIC to PIC communication will be needed in some embedded applications. We have two options to transmit data through transmission lines. Parallel Transmission Serial Transmission Parallel Transmission Parallel Data Transmission In parallel communication an entire byte of data is transmitted at a time. That is each bit has dedicated line. Thus for 8-bit data transfer we need 8 dedicated lines as shown above. Serial Transmission Serial Data Transmission In Serial Transmission only one bit of a byte is transmitted at a time. There is only one communication line, thorough which...

July 3, 2012By MikroC, PIC Microcontroller, Tutorials, , , , 49 CommentsRead more...
PIC16F877A

Using Interrupt with PIC Microcontroller

Introduction Interrupt is the one of the most powerful feature in embedded applications. Almost all the real time applications are implemented using Interrupts. So what is an Interrupt...?? As the name suggests Interrupts are special events that requires immediate attention, it stops a microcontroller/microprocessor from the running task and to serve a special task known as Interrupt Service Routine (ISR) or Interrupt Handler. Suppose you are at home, taking coffee. Suddenly your mobile phone rings. You stop taking coffee and answer the call. When you have...

June 28, 2012By MikroC, PIC Microcontroller, Tutorials, , , , 27 CommentsRead more...
Comparator Symbol

Using Analog Comparator in PIC Microcontroller

Comparator Module in PIC Analog Comparator is a device which compares two voltage signals and switches its output to indicate which one is larger. The analog comparator is used in many applications such as battery charger, analog to digital converters, IR sensors where we need to compare two signals. Most of the PIC Microcontrollers have built in Comparator Module which makes ease of design and saves cost. For demonstration, we use PIC16F877A. PIC16F877A consists of two analog comparators which can be used in eight different...

June 25, 2012By MikroC, PIC Microcontroller, Tutorials, , , , 12 CommentsRead more...
>